Designed to clear different types of products, plumbers consider drain snakes tools that cater to smaller drains like your kitchen or bathroom sink. The drain snake takes care of pipes ranging from 1-1/4″ to 2″ in diameter. Conversely, drain augers tackle larger pipes like bathtubs and shower heads.
Drain snakes are available in a wide variety of sizes and shapes, and they come in many different materials. Some are made of plastic, while others are constructed of wood, metal, or fiberglass. You can also choose to have your snake professionally installed by a professional plumber.
Table of Contents
How do you recoil a drain snake?
To recoil a drain snake, you need to insert the new cable through the hole in the back and guide the wire around the outer perimeter of the auger’s drum. When you establish a foundation around the edge of the container, you will be able to pull the snake out of the drum.
Drain snakes can be cleaned by soaking them in water for a few minutes, then rinsing them under running water. You can also use a mild detergent, such as Dawn dish soap, to remove the dirt and grime from the drain.
How long does it take to snake a main drain?
It takes about five minutes for a plumbing professional to snake a drain. All the plumbing in your home is impacted by the main sewer line. I know if my clogged drain is a main drain or a secondary drain? the clog is located at the bottom of the drain. If it’s a primary drain, you’ll need to replace the main line with a new one.
Secondary drains are usually located in the basement or crawl space. You can find the location of your main and secondary drains on your property by following the steps below. The drain should be clear and free of debris. If you see any debris, call your local plumber. They’ll be able to tell you what type of drain it is and how to fix it.
Do you have to remove toilet to snake?
The snake machine simple clogs only involve the toilet trap which is attached to the fixture and does not require disconnection of pipes or removing the toilet from the floor. If you buy an auger tool from a hardware store, you can use it to drill a hole in the bottom of the clog and then use a screwdriver to remove the trap.
If you want to make your own, you’ll need a drill, a small drill bit, and a pair of pliers. If you don’t have any of these items on hand, then you can also buy a set of 3/8″ drill bits from any home improvement store for about $1.50. The drill and bit are the most important parts of this project, so make sure you have the right tools for the job.
Why won’t my snake go down the tub drain?
The answer could be that you are using the wrong type of drain snake, that you are trying to force it through a P-trap, or that the water pressure is too high. If you have a standard drain pipe, you will need to use a special type of snake. The standard snake is made of stainless steel, and it is very strong.
It will not bend or break under the pressure of water. However, it does not have the same strength as a snake that has been treated with an anti-corrosion coating. This is because the coating prevents corrosion, but it doesn’t prevent the corrosion from happening in the first place.
In other words, if you put a coating on a pipe that is already corroded, that coating is not going to protect it from further corrosion. So, the best way to prevent corrosion is to make sure that all of the pipes in your home have been properly treated.
How do you turn a drain snake into a corner?
Bend the end of the snake about 3 or 4 inches from the end before you insert it so it will more easily go around the corner when it encounters it. When you get to the last few inches, you can try pulling back on the cable.
Is auger better than plunger?
The first thing you’ll want to do is tackle a small problem with a tool. For more stubborn clog, an auger is your best bet. Clean up the clogged area with an abrasive cleaner. You can use a mild soap and water solution, or you can go for a more aggressive cleaner like WD-40.
Either way, it’s important to get rid of all the dirt and grime that’s accumulated in the area. If you’re using a cleaner, be sure to use it in a well-ventilated area so that the fumes don’t get into your eyes, nose, and mouth.
Can a drain auger damage pipes?
These are supposed to be used by anyone to clear a drain. If the drain was used wrongly, it could make the problem worse.
“It’s not a good idea to use an auger to remove a clogged drain unless you know what you’re doing, and you have the proper tools to do it safely,” Dr. Michael J. O’Brien, an assistant professor of emergency medicine at the University of Texas Southwestern Medical Center in Dallas.
