The drain stub-out extends from a fitting, usually a sanitary tee, to a point 3 or 4 inches below the top of the toilet bowl. The drain-stub is designed to allow water to drain out of a toilet, but it is not intended to be used as a drain. It is used only to prevent water from seeping into the bowl, which can cause a buildup of fecal matter.
Table of Contents
Is it better to bend PEX or use elbows?
use pex bend supports instead of elbows. Without elbow support, it is possible to make a 90-degree turn with PEX tubing. For example, if you have a 3/8″ diameter pipe, you can use a 1/2″ pipe for a 2-foot length of tubing.
If your pipe is 1-1/4″ in diameter, then you will need to use 2″ tubing for the same length. Do not use PVC pipe with a diameter greater than 1.5″. This is because PVC is not a good insulator, and it will not be able to withstand the heat generated by the engine.
Where do I stub my toilet water?
The line should be inserted through the bottom plate on the wall, which is 8 inches to the left of the toilet’s center line. The sink has a water line attached to it.
Use a 90-degree elbow or stub-out fitting to insert the water line into the surface plane of your toilet. Connect the drain line to your sink’s outlet. If you have a sink with an outlet, you can use the outlet to connect the supply and drain lines.
Where is PEX not allowed?
You can’t install PEX in high heat areas like near recessed lighting. You can use a connecting material if you want to connect PEX directly to a hot water heater. Liquid can flow out of the other end if PEX is semi-permeable.
How do you cover exposed PEX pipe?
Stub out brackets are small tubes with a end. Most of the time they’re sold in chrome. If you don’t want to spend the extra money, you can also use a pipe clamp to hold the pipe in place. You can find these at any hardware store or online.
What is the purpose of a stub out?
Stub out elbows are primarily used when installing PEX pipe to stub out of the wall and allow for further connection of outlet stop valves and plumbing fixtures. Additional support for the pipe can be provided with the use of Stub out elbows with ears, which can be nailed to a wooden surface.
What size stub out for bathroom sink?
The standard size for a bathroom sink drain pipe is 1.25 inches in diameter. Depending on your state’s housing code, they may suggest 1.5 inches or 1.65 inches in diameter, and your home has a larger or smaller drain size. If you are unsure of the size of your drain, it is best to consult with your local building inspector.
How long do PEX pipes last?
Pex piping should last at least 50 years. The pipes should last up to 100 years under typical conditions. Extreme heat can cause PVC pipes to crack, which is why they are often used for drainage. PVC pipe is a type of pipe that is made of PVC (polyvinyl chloride) and has a diameter of 1/4 inch or less.
It is commonly used in the construction of plumbing fixtures, such as faucets, toilets, sinks, and shower heads, as well as in water heaters and air conditioners. In addition, it can be used as an insulating material for pipes, ductwork, pipes and other construction materials. Because of its low cost, PVC piping is widely used throughout the United States and in many other countries around the world.
Can hot and cold PEX lines touch?
The picture above is of PEX hot and cold water lines that have been run through the framing and are touching each other the entire way. This is ready for insulation and has passed the plumbing inspection. The picture below is a picture of a hot water line that has been running through a frame and has not yet been insulated. It will be insulated in the near future.
Why can’t you use PEX for tub spout drop?
I gather that 1/2″ PEX isn’t suitable to connect a tub/shower valve to the tub spout because the internal diameter of the PEX and especially its fitting is too restrictive, which will cause the water pressure to be too low.
