You should oil the valves at least two or three times a week to keep them in good working order.
Table of Contents
Do trumpets need valve oil?
The purpose of valve oil is to clean, lubricate and fill the air space inside the trumpet valves. You should oil the trumpet valves before each time you play, preferably without completely removing the trumpet valves. Accidental damage to the trumpet valve can be prevented with this.
If you are not sure how to apply the oil, you can use a small amount of WD-40 or other lubricant. If you do not have any oil on hand, it is a good idea to buy some from your local hardware store. The oil will last for many years and will not harm your trumpet.
How do I know if my trumpet is leaking air?
With a leaking instrument the pitches will be wide and feel uncenterd with logy responce. To seal “blow by”, a simple test is to coat the pistons with a layer of thick oil. You can play lip slurs and note the increased “lock” of notes.
When the valves are open, be aware of the firmer articulations. If the valve is not leaking, it is a good idea to replace it. We will do our best to help.
Can I use olive oil on my trumpet?
Mineral oil, olive oil, or other oils found in your home are not recommended for oiling trumpet valves. It is wise to wait until you can buy proper valve oil before using these, since they are easily accessible. The brass trumpet valve can be damaged by these home-remedies.
Can I use Vaseline on trumpet?
Every few weeks, most brass musicians grease their slides. As a general rule of thumb, don’t use vaseline or any other type of petroleum jelly on the tuning slides, they can cause seizing of the slides, and they can corrode the tubes. The grease that’s created for brass instruments is called slide grease.
How long should I let my trumpet soak?
The slides, the bottom valve caps, and the trumpet should be submerged. If you want to keep the felts dry, put some soapy water in a glass and immerse the valves. It’s best to let everything soak for 10 minutes or so. After the 10-minute soak, you can remove the valve and slide it back in.
If you’re using a slide valve, make sure the slide is completely dry before you remove it. You may need to re-soak it a couple of times to get it to be as dry as you want it, but it should be dry enough that you don’t have to worry about it getting wet.
Once you’ve removed all the excess water, it’s time to put the top valve cap back on. It’s a good idea to use a rubber band to hold it in place while you do this, so that it doesn’t slip out of place when you take it off. I’ll try to answer them as best I can.
How do you break in a new trumpet?
A new trumpet has a break-in period of about a month during which you should oil the valves and give the valves an oil change more often. The valves should be oiled at least once a week during the first month. After a few weeks, it’s a good idea to oil them every other day or two.
If you’re not sure how much oil to use, start with a small amount and work your way up to a larger amount as needed. If you don’t have any oil on hand, use distilled water instead of oil. You can also add a little baking soda to the water to make it easier to get the oil out of the valve.
Why is no noise coming out of my trumpet?
It’s most likely that one or more of the valves have been turned from their proper position, blocking the passage of air through the valve. If this is the case, you’ll need to replace the entire valve assembly. This can be done in a number of ways, depending on the type of valve you’re replacing.
The most common method is to remove the old valve and replace it with a new one. However, if you have a valve that’s been in use for a long time, replacing it may not be an option. In this case you may be able to find a replacement valve for less than the cost of replacing the original.
What kind of oil is used for trumpet?
Trumpet olive oil is needed to lubricate the valves of a trumpet. Trumpets with tight fitting valves will work well with thin-walled brass valves. If you don’t have access to a brass trumpet valve, you can use an old-fashioned brass or brass-plated brass valve. Brass valves are easier to work with than brass plated valves, but they are not as durable as brass.
