The garden hose needs to be connected to the drain valve. The equipment compartment on the outside of the bathtub should be next to the drain valve. If you are using a shower head, you will need to remove the showerhead from the tub and place it in the sink. This will allow you to drain the water from your tub.
If you do not have access to a sink with a drain, then you can use a bucket of water in your sink and fill it up with hot water. You can then use the bucket to fill up your bath tub with water and drain it.
Table of Contents
How do I drain the water from my spa?
The pump should be inside the spa. If your pump’s outflow hose is not long enough to reach a drain, connect it to a garden hose. The spa should run for a few minutes after the pump is turned on. If you’re using a pump with a hose that’s too long, you’ll need to shorten the hose to make it reach the drain.
You can do this by cutting a piece of PVC pipe about 1/2-inch in length. Cut the pipe so that it’s about the same length as the outlet hose, and connect the two ends together. Make sure that the end that you cut is longer than the rest of the length of pipe. Then, attach the other end to your hose and tighten it down.
Where is the valve to drain a hot tub?
The drain spigot is located on the outside of the tub, near the bottom rim. The primary and auxiliary spigots are used for draining the hot tub and bleeding the water out of the tub.
If you don’t want to use the drain plug, you can also use a hose clamp to secure it to the wall. You’ll need to make sure that the clamp is tight enough to hold the plug in place, but not so tight that it’s impossible to remove it.
How do you unlock the Arctic spa control panel?
All automatic functions will run as usual when the control pad is locked. “LocF” message will be displayed if a button is pressed down.
Simply press and hold the button for 2 seconds, and the keypad will be unlocked. ‣ ‣ LocP ” and † LocF ‡ keys can be used to move the cursor around the screen. The cursor will move in the direction of the button pressed.
Pressing the keys again will return to the previous position.
How long does an Arctic spa take to heat up?
It will take about 4 hours to heat up your hot tub to 100 degrees if it is located inside. The lower the outside temperature, the longer it will take for your spa to be ready. You can help it reach the desired temperature faster by leaving the cover on while it’s heating up.
If you have a large tub, you may need to leave it on for a longer period of time to get it to the temperature you want. If you are using a smaller tub or one that is smaller than the size of your bathtub, then it may be easier to just turn it off and let it warm up on its own.
How do you drain a hot tub fast?
Just long enough to let the hose prime and get the flow moving, and turn it on for a few seconds. The water can flow out of the tank if the vacuum is turned off and the hose is disconnected. If you’re using a vacuum pump, you’ll want to make sure the pump is turned off before you turn it back on.
If you don’t do this, the pressure will build up and you won’t be able to remove the excess water from the system. You can also use a hand pump if you have one, but be careful not to over-pressurize it, as this can lead to a loss of pressure and damage to your pump.
How long does it take to drain a hot tub with a garden hose?
The draining process can take up to 2 hours, but you don’t need to supervise if it’s properly set up. You should be able to see the water coming out of the drain after a couple of weeks if you make sure the hose is actually draining to the correct location.
How often should you drain your hot tub?
It should be drained about three to four times a year. The time it takes to drain your hot tub is usually around an hour or so. Four hours of your time is all you need to make sure that you are completely drained.
Can I drain my hot tub on my lawn?
Chlorine and bromine are harmful chemicals that can kill your grass and make your lawn discolored. Run your hose or drain away from grass or vegetation and away from the foundation of the tub. If you have a pool or spa, make sure the water is not too hot or too cold.
If the temperature is too high, the chlorine in the pool water can kill the beneficial bacteria that keep your plants healthy. Too low a temperature can cause the bacteria to die and the plants to wilt.
How do you flush out a hot tub?
To properly system flush your tub, remove the filters turn on the jets and pour System Flush directly into the filter compartment. If you have a jet pump on your tub, open the waterfall and turn the jets back on.
If you don’t have a waterfall, you will need to run the jet pump for a few minutes to get all the water out of the system. If you are using a water softener, make sure to turn it on before you start flushing the tub. This will ensure that it is working properly.
Can I drain my hot tub into the street?
If the water is chlorinated, you should drain it into the local sanitary sewer line for safe disposal. If you have treated and dechlorinated the hot tub water, you can drain it to the public water supply.
