How To Change Diverter Valve On Shower? (Check This First)

If only a few drops of water come out of the shower head when you pull the diverter, then you need a new tub spout and diverter. It is easy to find such components at most hardware stores.

Since one look is worth a thousand words, we recommend you check this detailed youtube video.

Can I replace the diverter valve?

You’ll need to take the old stem to the plumbing supply store so you can be sure to get an exact replacement. You pulled out the old diverter valve, and the new one slips right into the pipes. It is important to use the faucet that came with the new one. If you don’t have access to plumbing supplies, you may be able to make your own.

If you have a drill press, use it to drill a hole in the bottom of the sink and then use a screwdriver to pry it open. You’ll have to be careful not to cut yourself on the drill bit, but it should be easy enough to do.

How do you remove a shower diverter from the wall?

All you need to do is turn the cap and it will come off. You can get access to the bolts that hold the diverter in place by taking a screwdriver and removing the screws below the cap. Now that you’ve removed the caps, it’s time to unscrew them. To do so, you’ll need a pair of pliers and a small flathead screw driver.

How To Replace Valve Stem Seals? (Explanation Inside!)

You’ll also need some sort of tool to pry the threads off of the bottom of each cap. If you don’t have one of these handy, I’d recommend getting one from a hardware store, as they’re pretty cheap. Once you have all of your tools out, pull the two halves apart. The bottom cap will be on the left side, while the top cap should be the right side.

Be careful not to pull too hard at this point, or you may damage the plastic. It’s a good idea to have a friend hold your hand while you’re doing this so you can keep an eye on your hands and not accidentally break anything. Now you should have two pieces of plastic that are about the same size and shape.

Can a shower diverter be repaired?

Don’t delay in repairing your shower diverter once you’ve determined it’s broken. A broken shower diverter can lead to a poor shower experience. Repairing a shower diverter is a home improvement project that should be done as soon as possible.

How much should a plumber charge to replace a shower valve?

Labor cost for plumber to replace shower valve Plumbers charge $100 to $300 for labor alone to replace a shower valve or $225 to $575 for the valve with installation. Depending on the type and accessibility, it takes 1.5 to 3 hours to replace a shower valve. cartridge.

The cost depends on the size of the heater, the type of water, and whether it is a gas or electric heater. A gas heater can be installed for less than $500, while an electric-only heater will cost about $3,200.

How To Install A Shut Off Valve For Toilet? (Detailed Guide)

Can a shower diverter cause a leak?

Water only flows out of the tub spout or the showerhead when the diverter valve is working. As shown in the photo below, diverters leak a lot, allowing water to flow out of the tub spout even when it’s in shower mode.

Diverter valves are designed to prevent water from flowing into the bathtub, shower, or tub from the outside. They are also designed so that water can only flow from one side to the other. This is why they are called “diverters” and not “faucets.” .

Why does my shower diverter not work?

The most common issue with a shower diverter is when water comes out of both the tub faucet and the showerhead. Check to make sure the shower diverter lever doesn’t get stuck. The problem could be worn out parts in the shower head.

How do you check a diverter valve?

After you remove the lid of the boiler, you have to locate the diverter valve mechanism. Run tap water on hot and observe the diverter valve. If you run hot water, the valve is supposed to close in order to move the water to the tap. If you don’t see any movement, it’s not working. You’ll need to replace it.