Draining a pool doesn’t require much in the way of tools or materials. Enough garden hose to reach from pool to pool, and enough water to cover the entire pool are available for purchase or rent. Prepare the pool for draining. The easiest way to do this is to use a bucket of water and fill it to the brim with water.
If you don’t have a full-sized bucket, you can fill a small plastic bag with a little bit of sand or gravel and place it over the bottom of your bucket. This will make it easier to lift the sand and gravel out. You can also use your hands, but be careful not to get any sand in your eyes or on your skin.
Attach the garden hoses to your pump and set it in place. Make sure the hose is long enough so that it can reach all four sides of each pool and is at least 6 feet (1.2 meters) long. Be sure to attach the ends to each other, so you won’t be able to pull them apart when you’re done.
Table of Contents
How can I drain my pool without flooding the yard?
A medium-size water or vacuum pump is all you need. The outlet hose should be placed so the exiting water doesn’t flood the area. If you’re using a pool pump, you’ll want to make sure that the water level is at least 1/2 to 1 inch above the floor.
If it’s too low, it may not be able to drain off enough water to fill the tank, and you may have to add more water. You can also use a hose clamp to hold the hose in place.
What is the fastest way to drain an inground pool?
The easiest way to lower the water level is to place the multiport valve into the waste position and roll out the backwash hose. To lower the level of the pool, backwash the filter if you have a slide.
(Push-Valve) from an In-ground Pool If your pool is located in an enclosed space, such as a basement or crawlspace, it may not be possible to remove the slide from the bottom. In this case, use the same method as described above for removing a filter.
However, if you do not have access to a drill press, or you are unable to drill a hole large enough to fit the valve, then you may need to use a hand drill. To drill the hole, place a small piece of wood or other material between the drill bit and the PVC pipe. The hole should be about 1/2 inch in diameter, and about 3/4 inch deep.
Then, using a 1-1/8-inch-diameter hole saw, drill through the wood to the other side. Be careful not to cut the pipe, as this may damage it.
How much does it cost to drain a pool?
Pros will typically charge between $70 to $150 to drain a pool, but additional charges could come if you need chemicals, plus the best pool installation companies may offer some draining services for a discount if they know you’ll be using the pool regularly.
Can I drain my pool into the street?
In simple terms, you cannot drain pool water into the streets, curbs, catch basins, gutter, ditches, channels, and ultimately into the storm drain. Storm drain’s purpose is to guard against flooding and water damage by quickly removing rain from the ground. In addition, storm water drains are not designed to handle the volume of water that flows through them.
For example, a typical storm drain in the United States has a capacity of about 1,000 cubic feet per second (cfs), which is about the same as the flow rate of a 100-gallon drum. In other words, if you were to fill a drum with water, it would take about 20 minutes for the water to flow through the drain.
This is not a very efficient way to remove water from a drainage system, especially when you consider the fact that it takes a lot of energy to pump water through a drain, which means that the energy used to drain the system is a significant portion of the total energy required to operate it.
(For more information on energy use in drainage systems, see “Energy Use in Drainage Systems” on the Energy Information Administration’s website at www.eia.gov.
How do I get the last 2 inches of water out of my pool?
use a wet vacuum to suck the stagnant water from the pool. The liquid should be swept into the drain. To get rid of any water that may have accumulated in the liner, flip the pool liner over on your property. If you do not have access to a dry vacuum, you can use a vacuum cleaner to remove the liners from your pool.
You will need to use the same type of vacuum that was used to clean the water from the bottom of the tank. This vacuum will not be able to vacuum the entire pool, so you will have to do this on a regular basis.
